Anker’s Ultra Slim Extended Battery Case provides the best combination of good performance, price to the capacity, and physical size (the quantity of bulk it adds to the phone). It offers the ability to offer 117 percent of the full charge for an iPhone 6 or 108 percent to a iPhone 6s. The cost tag, $40 around this writing, is crazy low to get a battery case: In that rate, the Ultra Slim delivers the best charge value (a 2.9 percent charge per dollar, or $34.34 for a full charge, to the iPhone 6) of any one of the cases we tested, certainly.
The Ultra Slim doesn’t have an especially premium feel. That’s not saying it comes off as cheap, but nothing about its physical construction is extremely impressive alongside other cases. Another minor strike against this Anker case is its insufficient button coverage; we usually prefer (well-designed) press-through button covers that protect the iPhone’s various buttons and lower the number of places where dust and dirt can get underneath the iphone6 case manufacturing.
For your iPhone 6 Plus and 6s Plus
Anker doesn’t make an Ultra Slim for the iPhone 6 Plus or 6s Plus, so for people handsets, we love to the Tylt Energi Sliding Power Case. Unlike most of the models we tested, this one has a separate protective case that you could slide from the battery sled once you don’t have to have the extra power, which makes it an even more-practical choice for the already huge Plus models. It’s also a great source of energy, providing on average a 93 percent charge towards the iPhone 6s Also in our tests.
An important thing to not forget together with the cases we dismiss below is because they usually are not necessarily bad. Although we’re noting any issues we saw by using these cases, some of them are fine-they merely can’t quite match towards the premium quality in our picks.
Our previous pick to get a more protective case was Speck’s CandyShell. A perennial favorite, it offers two layers of material-plastic externally, rubber internally-that supply more protection than case designs that are just one or perhaps the other. The CandyShell is 10.9 mm thick, which puts it around the chunky side, nevertheless it doesn’t feel exceptionally bulky, and it’s one from the only cases we tested which claim in order to meet military drop-test standards. Speck offers the case in an array of colors, and variants add rubbery grips (CandyShell Grip), credit card holders (CandyShell Card), and graphic prints (CandyShell Inked).
The CandyShell carries a few problems that make it from becoming a top pick, though. For beginners, the CandyShell’s glossy back quickly attracts small scratches that generally aren’t visible head on but jump out once you view the iPhone in an angle. Granted, these scratches don’t impact the protection the situation offers-and we’re obviously happier to discover scratches about the case rather than in the phone itself-but it might be nice if Speck were to give the case having a matte finish.
Other concern is the case’s shape. Some of our readers, and also a contingent of Amazon reviewers, take trouble with the fact that the CandyShell’s back is slightly convex. Specifically, if you set the way it is with a flat surface, this “hump” causes the case to rock if you press along any kind of its edges, or spin like a top when you push it. (In the event you purchased a CandyShell and also you mind this spinning and rocking, Speck says to contact its customer care department.)
OnePlus (the Android phone maker) surprisingly decided to get in about the iPhone-case game having its Sandstone Case. The major draw is OnePlus’s Sandstone texture; TIME states that it “feels like smooth sandpaper” and this “[i]t’s super grippy, so that it is very difficult to drop.” Unfortunately the way it is is actually a shell with open top and bottom edges, meaning it’s less protective than the usual good case needs to be. Due to this design drawback, it fell from competition.
SwitchEasy has a mixed history, one that makes it hard to tell the total story depending on its cases alone. Its Numbers case was our original pick for your iPhone 5 and 5s, before a wave of reader complaints about quality and customer satisfaction. The answers we got from SwitchEasy weren’t thorough; mostly, the company blamed the issues on third-parties selling knockoffs from the products. (At iLounge, I stumbled upon the SwitchEasy protectors to get impressive generally speaking-the Numbers earned a rare A rating from me-but readers there contacted me about similar issues.) Ultimately, we pulled our recommendation.
With all of that at heart, we looked at three SwitchEasy cases for that iPhone 6. The first is the Odyssey. Like some of the better cases we’ve evaluated, it’s a mixture of plastic and rubber. As opposed to being layered, the type of material run side by side, using the hardened rubber making up most of the case. It isn’t the prettiest case, in our opinion, yet it is protective. It covers the buttons without reducing a lot of their clickiness, and six holes along the important thing up precisely with the speaker vents. The most popular section of the case is the port protection: Rubber protectors fit into the headphone and Lightning ports, respectively, when they’re not being utilised, keeping dust and also other debris out.
SwitchEasy’s Tones includes exactly the same port protection and uses a similar materials. The body is generally plastic, though, with all the rubber walking around the edges being a border and also across the back of the truth, matching the iPhone’s antenna lines. We’d want a layer of rubber between the handset and also the plastic back of the TPU iphone6 case supplier, and also the Sleep/Wake button demands a bit too much pressure on the few units we tested.
Our initial impressions of SwitchEasy’s Numbers were very positive-we were prepared to name it as being our top pick-but there’s a lot more to the story than only our review units, therefore we found a significant fault after a little extended use. This example is almost identical to the Incipio NGP, nevertheless it offers more protection. Instead of leaving the phone’s ports totally exposed, the case provides protectors that fit in to the headphone-jack and Lightning-port openings to maintain dust and debris out. It’s a fantastic touch that’s executed well. Even phone’s speaker is better protected, with six individual holes as opposed to one long opening. We actually just like the tactility of your devqpky94 a little bit more with SwitchEasy’s model compared to Incipio’s case, too. An early yellow version of your case we tested accumulated permanent stains, but later iterations exhibited no such issue. The problem is that the situation is a bit too loose, and so the corners appear too easily. We experienced this issue over and over while taking out the encased phone from our pockets. Because we’ve had other difficulties with SwitchEasy cases previously, we’re still a bit wary. If you opt to invest in a SwitchEasy case, we recommend buying it directly through the company’s website. The process will eliminate any potential warranty complications with third-party sellers, should you have any problems with the situation.
An important thing to keep in mind with all the cases we dismiss below is the fact, unlike with other kinds of products we cover, they are not necessarily bad. Although we’re noting any issues we saw using these cases, many of them are fine-they simply can’t quite match on the top quality of our own picks.
Combining a rubber skin using a plastic frame, the Spigen Neo Hybrid is actually a slim, attractive case. Its fatal flaw lies in its button protection. The silver plastic pill over the Sleep/Wake button doesn’t depress properly, so it may possibly not hit the control underneath, so you likely won’t feel it when it does. Former Sweethome editor Joel Johnson confirmed this concern together with the iPhone 6 Plus version. Because we received this case for testing so early, we think Spigen might revise later editions to manage this concern.
Also from Spigen is definitely the Ultra Hybrid, a single-piece case that fuses a rubber frame by using a clear plastic back. It’s a great-looking case, but once again, it offers problems with the buttons. As an alternative to putting raised material over them, it provides right and left edges which are flat all the way through with small indentations. For the Sleep/Wake button, the indented label says “PWR,” and then for volume, you will get plus and minus signs. Without a more pronounced physical distinction, you can more easily miss the buttons, and also the frame moves inward once you press.
Twelve South is up front about precisely how protective the SurfacePad is. Within the FAQ section of the case’s website, the company says, “SurfacePad for iPhone is not built to protect iPhone from falls, drops, being run over with a car or dropped inside the loo. SurfacePad is supposed to guard your iPhone from scratches and scrapes from things like car keys, nail files or concrete park benches.” It’s actually a smaller case plus more of a leather sticker using a cover. The SurfacePad adheres to the back of the iPhone, and you could eliminate it and reapply it as being necessary (though doing so will not be as basic as the company could have you believe). We love to the type of material, however the SurfacePad is difficult to recommend unless your primary dilemma is fashion.
The Vault Slim Wallet from Silk is really a much-less-expensive alternative to sister company CM4’s Q Card Case. It’s essentially the same design, except rather than a faux-leather back, the whole thing consists of TPU. Such as the Q Card Case, the Slim Wallet can take three cards, but an elevated arch in its card slot causes the cards to curve into a noticeable degree, which can damage the cards over time. The Q Card Case’s positive attributes otherwise carry over, but because of the card bending, I’m a little wary of the Slim Wallet.
Silk even offers the Armor Tough Case and PureView Clear Case. The Armor Tough Case is a rubber case with interchangeable, polycarbonate-plastic backplates. It’s an excellent case at reasonable prices, but it’s thicker than than our top pick, the NGP. The PureView Clear Case, however, is really a nice pick from the very full category of cases with rubber edges and clear backs, and Silk prices it aggressively. But we’re not terribly partial to this style as a result of dust’s propensity to acquire below the transparent back, as a result of the convenience in which the plastic can scratch. Still, next to others we’ve tested, the PureView Clear Case has pleasant-feeling buttons and well-sized port openings.
With Incipio’s Rival, unlike with all the NGP, simply the border is TPU; the remainder of the Rival is challenging plastic, about .3 mm thicker compared to the NGP. Everything regarding the case is basically similar to around the NGP, including the cutouts to the ports and the caliber of the button protection. As the Rival is extremely smooth, much like the NGP, horizontal lines throughout the lower two-thirds from the back include a distinct texture. It isn’t as neutral as being the NGP, but if you want the design and style, it is actually a wise decision.
Tech21’s Evo Mesh, which features the next generation of your company’s shock-absorbing lining, is surely an Apple Store exclusive. Much like Tech21’s Classic Shell (more on this design below), it’s a rubber case having a colored band running around the perimeter. The dimensions are virtually identical involving the two. There’s something concerning this one that people like over the Classic Shell, but it’s hard to put a finger on what that is. Perhaps it’s how the somewhat-obnoxious orange band has become replaced by colors matching the various body shades of your case itself. Overall, though, this case is simply too pricey for what it gives you.
Plastic and rubber by using a clear back, the ITSKINS Venum Reloaded drops the ball when it comes to covering the iPhone’s buttons. The same as the setup of Spigen’s Ultra Hybrid, the design from the Venum Reloaded makes hardly any physical distinction in between the button coverage and the rest of the case. This example have also been relatively expensive when last we checked, along with the plastic border frame feels fragile.
Really a greater portion of a fashion case, the Nitro Forged from ITSKINS currently costs a fairly penny at nearly $70. It is made up of rubber skin with machined aluminum caps that attach at the top and bottom. Thankfully, this design is definitely an improvement over previous versions, which required one to make use of an included screwdriver to install and take away the caps; instead, it uses small plastic clips that one could put in and take off manually.
Also from ITSKINS may be the Evolution. A rubber core by using a plastic frame, the Evolution has some curves which help help it become feel slightly more organic. The large problem is that the screen rises over the side of the case instead of the opposite. Because of this when you drop your handset, there’s far more prospect of harm to the display when compared with other cases.
Incipio makes a lot of cases that we can’t expect great things from every one. The Advantage is really a plastic slider, a style that’s relatively rare these days. The smooth, matte-finish plastic splits into two pieces for installation and docking purposes. Though it offers proper button coverage plus a nice protective lip, we found the truth to be too tight; pulling it off, particularly the bottom cap, is a struggle.
Weighing several grams a lot more than the normal of the cases we tested, the DualPro SHINE is actually a solid contender from Incipio. It incorporates both plastic and rubber layers, although as an alternative to being molded together, they’re two distinct pieces. The rubber is quite thick but doesn’t dampen the tactility in the buttons at all, and it still provides acceptable access to the ports. The port openings are identical to the NGP’s. We also checked out the typical DualPro, which has a matte finish. It’s quite nice, but it’s thicker in comparison to the NGP and lacking the mil-spec rating from the CandyShell.
The plastic layer from the DualPro SHINE suits grooves from the rubber, helping the case think that a cohesive unit. We think the most polarizing thing about this case is its texture: Designed to seem like brushed aluminum, it certainly doesn’t think that that, as well as at least within our tests, the result is a certain measure of cognitive dissonance. It’s not a bad thing at all, but overall it really doesn’t feel as nice because it looks.
If card storage is important for your needs, Verus’s Damda is actually a fine case. The entire body is made of black rubber, with nice button protection and effectively centered openings for your headphone port and microphone, the Lightning port, and the speaker. Linked to the back is actually a plastic compartment that adds both mass and depth. A plastic door slides ready to accept reveal space for two, maybe three, charge cards. We initially found it a little bit challenging to open, but with some cards in there it’s easier to use yet still secure. This is certainly even more of a niche market case than our pick.
Verus’s Crystal Mixx offers a transparent window including a rubber frame. Your back about this one is plastic, which can be one of these two drawbacks. In your exposure to iPhone cases, clear plastic scuffs easily and definately will show those scratches within dependent on days. This situation is probably not so bad in the event the frame provided a much better lip. Unfortunately, at .3 mm, it’s one of the shortest lips we saw, and yes it may lead to problems when you drop your iPhone.
The Protector Case and Voyager Case from Pelican look a whole lot alike, with each model is hard to find-Pelican doesn’t sell them online, and then in our experience they’ve been reliably available limited to AT&T retail shops. The Protector can be a bulkier, more-angular take on the CandyShell design with no additional benefits, so we’d pass onto it. The Voyager adds port protection and funnels the sound from the speakers forward. Furthermore, it comes with a belt clip and screen film. We percieve this model as an option to an OtterBox case, as it’s basically overkill. The majority of people simply don’t need this amount of protection, especially not when they have to fall out of their strategy for finding it.
PureGear’s Slim Shell Case is available in seven color combinations, including clear-on-clear. This model is difficult plastic having a rubberized yet still rigid frame. The metal button covers are a really nice addition, improving the case feel more premium. It won’t offer as much protection as a CandyShell, thus it isn’t a high pick, but this one isn’t an unsatisfactory option by any means.
One of the first iPhone 6 cases to become publicly sold-we saw it around May 2014-Minisuit’s Frost is surely an inexpensive TPU skin. While it does fit, it provides virtually no lip, as well as the holes down the bottom are uneven to begin looking warped.
Monoprice is recognized for inexpensive products of all kinds. We love a few of the company’s accessories-this makes great cables, by way of example-but Monoprice cases generally don’t impress. The type of material often feel cheap, as well as other companies offer higher-quality products at similarly low prices. For example, the Metal Alloy Protective Case (offered in gold, silver, and cosmic blue) includes a thin, aluminum shell that snaps over a thin TPU skin, with lines matching the iPhone’s antenna breaks. The TPU doesn’t feel as nice as being the material that Incipio along with other companies use, as well as the case exposes the Apple logo on the rear of the phone.
Monoprice’s Industrial Metal Mesh Guard Case (in black or white) feels a little nicer but is even less protective. The plastic shell has features a cool-looking steel grille over it, however it leaves the very best and bottom edges unprotected, and yes it features the most important Apple-logo opening we’ve seen on any case.
We checked out the TPU case from Insignia, a Best Buy brand, and yes it is apparently in the same OEM as Monoprice’s TPU case, but in a higher price.
We don’t such as the Monoprice PC TPU Protector Case as much, though it does offer arguably more protection. This model splits into two pieces, having an inner skin of TPU as well as a polycarbonate shell that snaps into position over it. The case is rather simple to assemble, but when it’s together, it simply feels big. It’s both wider and thicker compared to NGP, with no obvious advantage other than price.
Rokform has long dedicated to ruggedized cases that can get connected to an ecosystem of mounting accessories. Its Sport v3 is no exception. This plastic and rubber case comes with swappable magnetic backplates that allow it to connect to various mounting brackets the business sells. Unfortunately, the instruction insert lists a dealbreaker: “Magnet will disable NFC on phone.” Nowadays the organization claims that the magnet won’t hinder Apple Pay or any antennas, but we haven’t tested this.
OtterBox’s Defender Series will be the bulkiest of the cases we’ve tested thus far. Here is the company’s flagship case, the one a lot of people associate using the brand. It’s composed of a plastic frame that snaps across the handset plus a thick rubber skin that covers the whole thing. Unlike most other cases, this model includes flaps over the vibration control switch, headphone port, and Lightning port-all great things to have an extra amount of protection. It also includes button coverage, but we found out that it requires more force to depress the volume and power controls than other cases do.
The Defender Series is additionally the only case we’ve tested with built in screen protection as a specific film integrated into the frame. Simply because you get a little bit of space involving the protector along with the screen, very light presses and swipes might not exactly register, which is a drawback. Atop the Touch ID/Home button is a thin sheet of plastic that didn’t hinder the knowledge inside our testing. Even though the Defender Series does expose the Apple logo, the way it is at least covers it with clear film that prevents it from getting scratched. So when an additional benefit, the Defender Series includes a belt holster.
Inside the OtterBox family, the Commuter Series represents the next thing down in overall protection. As an alternative to plastic inside and rubber on the exterior, the layers are reversed. The way it is still offers port coverage, nevertheless the switch around the iPhone’s left side remains exposed. Thankfully, the buttons depress much more easily. Rather than a permanent screen protector, OtterBox includes an optional film with this particular case. The Apple logo is again exposed, now without having plastic covering it. Aside from the port protection, this case offers no obvious benefits more than a CandyShell, as well as the dimensions are a drawback that keeps this model from earning a top-notch spot.
The Symmetry Series is a relatively recent accessory for the OtterBox lineup along with the slimmest of those all. It seems like a direct response to the CandyShell, featuring its dual-layer design. This situation offers the same degree of protection as our top choice plus a substantial lip. It’s taller and wider, though, with a higher price. The biggest benefit is using a matte-plastic back, it won’t show the scratches that the CandyShell does.
OtterBox’s newest case, the Statement Series, is surely an iPhone 6/6s-specific case. An iPhone 6/6s Plus version exists, but unlike OtterBox’s other lines, this series offers no version for older iPhones or other flagship smartphones. It’s also one of your few OtterBox cases that put aesthetics first, featuring its large back-panel window and leather-covered lower quarter being its key distinguishing features. We’re testing the Statement right now, and we’ll decide whether or not this should join our picks soon.
The Tough Candy Cases Candy Clip Series is a fairly crazy proposition: For $30, you have a hard-plastic X-shaped piece that snaps onto the rear of the iPhone, covering its corners and some of the edges but leaving the buttons and most of the sides exposed. No thanks.
Urban Armor Gear’s Case is one of your only cases we’ve tested to fulfill military drop-test standards. It’s excellent like a protective case, nonetheless its industrial aesthetic lacks the broad appeal of simpler designs like those from Incipio and Speck. UAG also combines plastic and rubber in this instance, but rather than a glossy finish, it works with a matte one, with the industrial appearance that appropriately matches the brand’s name. With ridges and fake screws, it looks like something which would not out of place over a construction site. We do take issue with both the small, rectangular holes on the rear of the truth-about a quarter of how through the top or bottom, respectively, they expose part of the logo as well as the top 1 / 2 of “Phone” from the iPhone label. It’s an unusual design decision by using an otherwise impressive case. However, this model does include a screen film, whereas most iPhone cases don’t currently.
Tech21’s entire product lineup is founded on D3O, a certified material the organization uses in each and every one of their cases. Mostly present in the borders of Tech21 cases, the brilliant-orange material is supposed to remain soft when at rest but automatically harden upon impact, dissipating the force and ultimately preventing injury to your phone. The company really likes to exhibit the stuff; all of its cases are at least translucent, if not transparent, around the edges.
From Tech21, we tested the Classic Shell, Classic Shell Cover, and Classic Shell Flip. First is the standard, a glossy TPU skin that’s wider than the NGP, because of the layer of D3O. We’d like to notice a bigger lip than this example offers, as well as the buttons are a bit squishier than we generally prefer. The Classic Shell Cover keeps a similar frame but replaces the TPU on the back by using a hard-plastic plate, and contains an attached cover to safeguard the iPhone’s display. Anything else works just like together with the standard model, and also the lid has a cutout over the earpiece so you can speak on the phone from it closed. The Classic Shell Flip is essentially a similar, only as an alternative to plastic this situation carries a leather feel (it seems to be the fake stuff), and also the lid comes around from the bottom rather than the side. We find that lids get in the way a lot more than they assist, so neither of the covered models excites us, as well as the soft buttons and wider body of your Classic Shell prevent it from getting a recommendation.
From iLuv, we received two cases for evaluation: the Aurora Wave and Gelato. The first is a straightforward silicone skin by using a grid about the back that glows in the dark. When it comes to body coverage, the situation lives around what we’re looking for, but making this kind of design involves a low degree of difficulty. As we’ve often found with cases with this style in past times, the vertical edges can pull from the body in the phone more readily when compared with other cases, allowing dust and also other particulates to obtain underneath. The Gelato, however, is TPU iphone7 case with the attractive checkerboard pattern in the back. It appears and feels pretty decent, nevertheless the .33-millimeter lip is way too short.
Poetic’s Atmosphere is actually a thin case manufactured from dual-molded polycarbonate plastic and TPU. The softer material rings the front edge to produce a small lip, plus it runs on the antenna breaks on the back of the phone. Even though this transparent case initially appears like a good option for folks who desire a slim protector but nonetheless want to show off their iPhone, it falls short due to button protectors that need excessive force to press.
Macally shipped us some different cases, but two seem to be styles we simply can’t recommend. The Metallic Snap-On Case and also the Flexible Protective Frame come in a variety of colors, nevertheless the former can be a shell, and also the latter is a bumper that protects the sides but leaves the scratchable back exposed. The Durable Protective Case, in contrast, does offer more thorough protection, but unfortunately it isn’t an original design. A mixture TPU skin and hard-plastic frame, this situation form of looks like an armadillo in the back. We’ve already seen a minimum of one other company providing the same case, and we weren’t impressed with that case’s aggressive looks either.
New Trent’s Alixo 6S isn’t necessarily the prettiest case around, however it is one in the more original designs we’ve seen in the pile. This two-piece case is made up of front frame (black- and white-rimmed versions are included in the package) and a silicone rubber and plastic back. You merely snap the phone into your selection of frame then insert it in to the back piece, consisting of flip-open port protectors. The amount of protection this model offers for the price is impressive, since it includes a built in screen film and Touch ID coverage. Although the latter happens to be the Alixo 6S’s downside: While the fingerprint sensor does deal with the thin material over it, we found so that it is less reliable, requiring more efforts to unlock the unit.
Marblue’s ToughTek is actually a thick silicone rubber case that accompany a screen protector. While we don’t doubt this thing will be able to tolerate some significant drops, the ToughTek is big-3 inches wide, 5.8 inches tall, and .6 inch deep-and particularly difficult to get in and out from tight pockets because of the grippy material. It may not be a bad option if you’re handing your iPhone 6 to kids.
The Elite, also from Marblue, takes its inspiration from your CandyShell, while incorporating an Aztec-like pattern. The plastic and rubber layers intersect in horizontal and vertical lines, using the latter material sticking up higher than the hard plastic. The most intriguing point about this case is the couple of inch-long ridges, one on either side. They’re made to work with an array of accessories, such as a belt clip. We’ll be keeping an eye out for these accessories, and we’ll decide if they boost the price of the truth.
We had high hopes to the Spigen Capella, which comes in multiple colors. Its setup is much like the CandyShell’s, with rubber inside and plastic outside. The large difference, along with the reason we had been excited about it, is it’s much slimmer, measuring about 2 mm thinner from front to back. This really is partly due to smaller, half-millimeter lip round the screen. One of the editors loves the way the case’s slight curve feels, comparing it to the iPhone 3G. Judging by the feedback we’ve seen from readers and Amazon reviewers, lots of people don’t like that shape around perform.
While the Capella isn’t as deep since the CandyShell, it is actually a bit taller, contributing to 3 mm wider. This width eventually ends up being problematic for two reasons, one on either edge. About the iPhone’s left side, the switch is quite a bit harder to toggle, as it’s deeply recessed inside of the rubber border; if you don’t have nails to communicate of, moving it forward and backward will likely be tough. On the opposite side, the Sleep/Wake button requires a surprising amount of pressure to activate. If you’re willing to deal with those drawbacks, the Capella is otherwise worth looking at like a CandyShell alternative.
Using its Revolution case, Poetic is looking to take on companies including OtterBox at a much lower price. The truth begins with a plastic frame that snaps to the front of your iPhone; a clear sheet of plastic protects the screen while leaving the sensors at the very top and also the Touch ID button at the end exposed. A rubber and plastic body fits around the back, snapping into position using the front piece. The whole thing feels quite sturdy, the buttons click well, as well as the flap on the Lightning port is a nice little bit of extra protection.
Supcase’s Unicorn Beetle Pro Holster offers a similar proposition. The largest difference between this model along with the Revolution is it comes with a plastic belt holster. Having roughly a similar dimensions since the Poetic case, this model requires an installation that’s pretty much the same. This example adds a few flaps for coverage, namely within the side switch and the headphone port in addition to the Lightning port. While it’s a really solid-feeling case, we immediately known as the company’s claim of dust-proof construction into question, since it leaves openings for dust to get in, such as the fully exposed speaker. Presently, Amazon users are typically fond of it, with 127 reviews and a 4.1-star (out from five) rating, but we’ve seen several three- and four-star reviews.
Relative newcomer Supcase has several iPhone 6 cases, in fact, most of that are portion of the “Unicorn Beetle” family. The Slim Armored Protective Case is a lot like Urban Armor Gear’s case in that it’s protective, although the design is rather specific, meaning it likely won’t entice the same wide swath of folks as something a little bit more generic. The plastic and rubber case feels sturdy and has several of the clickiest buttons for any we tested. When it comes to lip, it’s no more than .5 mm, so it’s small compared to we’d like, as well as the case makes no mil-spec claims. If you love the style, it’s not a bad choice otherwise.
Supcase also sells the Hybrid Clear Bumper Case, which combines a definite-plastic backplate having a TPU bumper. That polycarbonate back won’t absorb all the shock because the thick rubber border, but it’s a sensible way to show off Apple’s design.
Inside a previous version of the guide, we named Logitech’s Protection [ ] as a far more-protective pick. It possesses a very similar design, with the advantages of a matte finish and embedded magnets that give it time to connect to mounting accessories. Unfortunately Logitech has confirmed that it’s will no longer selling the case, which is currently on clearance at Best Buy.
Not one other case we tested is placed the same way as Maxboost’s DuraShield Series (now named DuraSLIM). Like various other models, it uses both rubber and plastic components, but here the rubber is actually a bumper that wraps round the iPhone’s border, as well as the plastic snaps in place over it while covering the rear of the handset. Despite the unusual design-or possibly because of it-the way it is offers superior protection in contrast to many others we’ve seen. It offers a 1-mm lip, plus speaker and Lightning-port protection. Furthermore, it redirects the audio ports forward, meaning the sound comes at you, instead of down; the design has no influence on audio quality, thankfully. As for the Lightning port, it stays protected underneath a rubber tab that you could flip out if you want access.
Few case manufacturers actively warn that the product doesn’t offer drop protection, however this type of message appears in the Amazon listing for Maxboost’s Liquid Skin. Extremely thin, this transparent-TPU case adds almost no bulk to the handset, not a protective lip. It’s better than a shell as it offers button protection and cutouts for that ports, even if they are quite tight. But with such a warning through the case maker itself, we can’t recommend the Liquid Skin for most of us. If you’re going to use a case, you should use something that’ll resist a drop.
Maxboost’s Crystal Cushion and that i-Blason’s Halo Series are almost identical to each other and in reality may be small tweaks on a single reference design. Have rubber frames-the Halo Series offers six colors, plus clear-with transparent plastic backplates. The Maxboost case’s edges are more squared-off, even though the i-Blason’s are rounder. Both offer good body coverage and responsive buttons, nevertheless the lip across the screen is almost nonexistent, especially on the Halo Series. Combine by using the tendency for clear plastic cases to scratch as well as to expose trapped dust underneath, and these cases aren’t top picks.
The Maxboost HyperPro Series is designed for all intents and purposes a thicker version from the Incipio NGP. Available only in black, it uses two layers of TPU to protect the iPhone, and yes it measures 10.2 mm thick; it’s also wider and taller than our pick. The buttons press well and yes it features a protective lip, but we could find no real help to this situation across the NGP, besides savings of just a few dollars.
One of only a few slider-style cases on the market, Maxboost’s Vibrance Series provides a different build than the majority of the cases we tested. A tough-plastic case, it splits into two pieces, both lined using a soft fabric along the back that’s designed to prevent damage during installation and removal. Instead of pushing the phone in the case, you accomplish the base cap, slide the phone in to the top, and after that push the pieces back together. Much similar to the STM Harbour, these kinds of design permits you to maintain the iPhone thoroughly protected quite often, and to plug it into docks when needed. The lip is almost short, though, and pulling off the Vibrance’s bottom cap is harder than flipping up the Harbour’s bottom. Maxboost also provides only one color choice, salmon using a gold cap, which can not attract as much people as increasing numbers of basic colors would.
If you realise the CandyShell being too large, you won’t be impressed with Speck’s MightyShell, which comes in black, orange, purple, pink, and clear variants. This model comes with several key differences. First will be the extra layer of TPU material which helps absorb shocks into a greater degree; it adds 2 mm both in width and height, in addition to .5 mm on the thickness of your case. Speck claims that the new design will “double MIL-STD-810G drop test standards,” but we can’t tell whether it means the situation is tested to thrive drops from doubly high or it means the situation can tolerate the regular 4-foot drops twice as often. One aspect of the case we really appreciate may be the hard-plastic exterior, that is matte as opposed to glossy, therefore it won’t show scratches as readily as the standard CandyShell. For the price, we expect not only claims of better drop protection; conditions in which this case would survive but a CandyShell wouldn’t are too ambiguous to warrant the fee.
Among ultrathin cases, Shumuri’s SLIM looks and feels very similar to Caudabe’s The Veil XT, as a result of the lack of the typical Veil’s screen-protection lip. But it’s also missing both Veil models’ camera-lens protector. The same thing goes for Monoprice’s Ultra-thin Shatter-proof Case (in clear frost, ice blue, and smoke) and Totallee’s The Scarf (for iPhone 6 and iPhone 6 Plus).
Rearth USA’s Ringke Slim (for iPhone 6 and iPhone 6 Plus) offers both a screen-protecting lip and bottom-edge coverage, and also thicker plastic for additional protection. However, we’re not fans of their aesthetics-since the case’s rigid plastic is thicker, the organization has added a small slit to every corner to produce putting the case on your phone easier. The design is successful enough; we just don’t like the actual way it looks.
Power Support’s Air Jacket and SwitchEasy’s Nude (for iPhone 6 and iPhone 6 Plus) are glossy-plastic cases which are slightly thicker than Caudabe’s The Veil. The first kind provides good coverage across the phone’s bottom edge but has only the really faintest of any screen-protection lip. The second has neither.
Amzer’s Crusta may well not look like an incredible value at $35 (iPhone 6) or $45 (iPhone 6 Plus) by this writing, nevertheless the package includes not just a simple case. The situation itself utilizes a two-piece snap-together design by using a rubber bumper along with a glass back that lets the iPhone’s rear show through. The glass likely won’t show scratches as easily as similar cases we’ve seen using a plastic back, but you will still see any dust, hair, or some other particulates that get underneath the glass. Amzer contains a second piece of glass to safeguard the phone’s screen. The case ends up being bulkier than we prefer-the iPhone 6 version is 14.4 mm thick, such as the phone-but it’s one of your better cases we’ve seen from Amzer, a business otherwise known for inexpensive, nondescript accessories.
NewerTech is well known more for computer accessories than smartphone accessories, although the company does give a type of cases called NuGuard KX (for iPhone 6 and iPhone 6 Plus). Made more for drop protection than sleekness, the NuGuard KX boasts a thick layer of gel material that absorbs and evenly distributes shocks. The truth is very bulky, yet an opening on the rear of the case for that phone’s Apple logo actually subtracts through the overall degree of protection. We prefer the NGP.
We have varying degrees of praise for 3 cases from Griffin Technology. The Survivor Slim (for iPhone 6 and iPhone 6 Plus) is our least favorite of those. This bulky rubber case feels a lot more like an accessory for a kid’s toy than the usual smartphone. It might be a good case if children frequently utilize your phone, but we suspect that most adults will prefer something slimmer.
We like the Survivor Core (for iPhone 6 and iPhone 6 Plus) and All Clear Identity (for iPhone 6 and iPhone 6 Plus) better. Both permit the handset’s back to show via a clear back panel. The first kind has rubber edges, as well as its rubber corners protrude a bit, helping cushion the iPhone against drops-however the outcome is that it’s a bit larger than a normal case. The All Clear Identity, on the other hand, has a transparent back with translucent-rubber edges. The situation, like all cases sporting a precise back, is both cases show any gunk that gets below the plastic. For many, that could be a sufficient compromise in a case designed to enable you to view your phone’s own surfaces, but we generally prefer something translucent or opaque. Neither the Survivor Core nor the All Clear identity is a bad option, but neither particularly excites us.
Belkin’s Grip Case for iPhone 6 is an excellent substitute for our top pick, but it doesn’t quite make your top tier. The design is much like that relating to the Incipio NGP, as it’s a one-piece polyurethane case. The biggest difference is across the phone’s bottom edge: Rather than having separate openings for that headphone jack, microphone, Lightning-connector port, and speaker, the situation exposes the last two through one long opening. A slight indentation from the plastic covering the base of the phone allows for use with accessories for example Apple’s Lightning-connector adapters. It is a nice feature we haven’t seen on other cases, although we worry the thinness from the material here, and also near the Ring/Silent switch, may make it more vunerable to ripping. Wirecutter editor Michael Zhao also finds the case’s button coverage to get somewhat problematic, since he doesn’t such as that they’re nearly flush with the case.
One of the cases shipped to us for consideration, we dismissed a variety of models right off the bat. We cut Spigen’s Slim Armor, Slim Armor S, Tough Armor, and Tough Armor S, in addition to Verus’s Thor, Iron Shield, and Dandy Diary, plus PureGear’s DualTek, due to their Apple-logo-exposing holes in the back. They generally do a good job of protecting your phone otherwise, but we can think about absolutely no reason to recommend them for most people when existing hole-free options are nearly as good or better.
We dismissed numerous shell cases because, since we mention above, they supply a minimal amount of coverage to the device’s body. Among they were the Aluminum Fit, Thin Fit, and Thin Fit A from Spigen. The same thing goes to the Neo Hybrid EX, Spigen’s bumper case, which offers much less protection.